Evolution EVO230-HDX Bedienungsanleitung PDF herunterladen (Seite 5)

MILJÖSKYDD

Återvinn de material du inte behöver istället för att slänga dem

i soporna. Alla verktyg, slangar och förpackningsmaterial

bör sorteras och lämnas på din lokala återvinningsstation

och kasseras på sådant sätt som är säkert för miljön.

Undersökningslista för återvinningsbara material

Material Vikt (Kg) Procent ( % )

Aluminum

Gjutjärn

Järnplåt

Plast

Övriga

Totalt

1.94

0.0

3.61

1.96

0.10

7.61

25.40%

0.00%

47.00%

25.70%

1.30%

Pakkausmateriaalit

Material Vikt (Kg)

Kartong

Polystyren

Polyetylen med låg densitet

Polypropylen

Övriga

Totalt

1.23

0.0

4.50

0.001

0.0

5.731

intended as a guide only and should not be relied upon for the accuracy

of a cut. Remove the battery compartment cover and t the supplied

batteries, taking care to observe the correct polarity, then replace the

cover. Press the switch to the on position to activate, and remember to

turn off the laser when you have nished a cut. Before use the sight must

be aligned by means of the adjustment screw. Important Notice: Do

not point the laser at anyone and NEVER look into the laser light, as

serious eye damage may occur.

Chip Collection

This tool is provided with a chip collector compartment. When the chips

accumulate up to the see-through window, remove the cover, clean out

the cover, then replace it, and tighten the knobs. Notice: The metal chips

inside the cover may be very hot and sharp - do not touch with bare

hands.

Maintenance And Troubleshooting

Keep tool, cord, and carry case clean and free from chips. Avoid using

cleaning products, which include benzene, trichloroethelene, chloride,

or ammonia as these can damage plastic parts. In case of electrical or

mechanical malfunction, immediately switch off the tool and disconnect

the plug. Excessive sparking may indicate the presence of dirt in the

motor or worn out carbon brushes. Check for wear and replace when

they reach 1/4” (6mm). For all other service take machine to your local

dealer, or to Evolution Power Tools USA, Iowa, if bought in the USA.

Lubrication

Your machine gearbox is lubricated at the factory. To check and / or add

lubricant, it is necessary to dismantle the tool. This operation should

always be handled by the nearest SERVICE CENTER or Evolution

Power Tools USA, Iowa, if in the USA. All repairs and servicing made

by these centers are fully guaranteed against defective materials and

workmanship.

Accessories – Genuine Evolution Blades

40T 9” (230mm) TCT Wood Blade

48T 9” (230mm) TCT Mild Steel Blade

60T 9” (230mm) TCT Stainless Steel Capable Blade

80T 9” (230mm) TCT Aluminium Blade

Notice: Fair wear and tear and damage caused by misuse is not

covered under the 12-Month guarantee.

Gebruiksaanwijzing

Belangrijk

De gebruiksaanwijzing en veiligheidsvoorschriften aandachtig

doorlezen. Het voltage veriëren en controleren of alle handgrepen

en onderdelen stevig vastzitten met het oog op uw veiligheid. Neem

contact op met uw distributeur in geval van twijfel.

De gebruiksaanwijzing op een veilige plaats bewaren

Specicaties voor het EVO230-HDX model

Motor (230V of 115V 50/60 Hz) (Watt): 1750

Maximale zaagdiepte (6mm dikte 90

) (mm): 84

Maximale zaagdiepte (6mm dikte 45

) (mm): 53

Maximale Zaagdikte (Plaat in zacht staal) (mm): 12

RPM onbelast (min-1): 2700

Aanbevolen maximale werkduur (minuten): 30

Geluidsdrukniveau (belast) (dB(A)): 108.7

Trillingsniveau (belast) (m/s

): 3.9

Gewicht (Kg): 9.0

30 5

1 2 3 4 5 6 7 8 9 10 ... 32 33

Kommentare zu diesen Handbüchern

Keine Kommentare

Evolution EVO230-HDX Bedienungsanleitung Seite 5

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Kreissägen Evolution EVO230-HDX