Evolution EVO230-HDX Bedienungsanleitung PDF herunterladen (Seite 4)

• Never use the tool without the original protection guard system.

Do not lock the moving guard in the open position.

• Always keep the power cord away from moving parts of the tool.

• When you put the tool away, switch off the motor and ensure that all

moving parts have come to a complete standstill.

• In case of jamming, immediately switch off the tool and disconnect

the plug.

• Before using accessories, always compare the maximum allowed

RPM of the accessory with the RPM of the tool.

•

Ensure that the cutting depth adjustment handle, angle adjustment

handle, and side handle are rmly xed whilst using the tool (g. 1).

• Only use the anges and washers that are supplied with the tool,

and replace them if they become damaged or scored.

Machine Set Up

Mounting / Removing TCT Saw Blades

Remove the chip collection cover from the machine by undoing the knob.

Undo the two screws to release the inside blade guard. Loosen the screw

that retains the spanner to the machine and remove the spanner. Undo

the M13 bolt that secures the blade (g. 3) and remove the blade ange.

Note: Use spindle lock. Replace blade, making sure that the arrow for the

direction of rotation of the blade matches that of the machine then tighten

the M13 bolt with the ange in the correct position. Note: Check that the

spindle lock is fully released by manually rotating the blade before use.

Ret the spanner to the holder on the machine and tighten the retaining

screw.

Adjustment Of The Cutting Depth

Release the handle to adjust to the required cutting depth. Ensure that

the blade protrudes a maximum of 3/16” (4mm) through the material

being cut. Tighten the handle to lock in position. Note: The safety guard

(g. 1) is marked in increments from 0 – 84mm to assist in setting the

depth of cut.

Adjustment Of The Cutting Angle

Release both locking handles (g. 2) and adjust to the required cutting

angle by lining up the mark with the printed scale. Tighten both handles

to lock in position. Note: There are certain compound cuts on which it

may be necessary to manually retract the guard to allow the blade to

enter into and / or through the cut.

Line Of Cut Guide Slots

Guide slots are provided at the front of the saw base. The left slot is used

to follow a line when making a 90-degree cut. The right slot is used to

follow a line when making a 45-degree cut.

Operating Advice

Always clamp the work piece on a rigid support such as a bench or saw

horses where possible. This tool is equipped with a safety start feature –

to start the tool, you must rst push in the switch on the side of the handle

with your thumb – you can then depress the main trigger switch to power

the motor. Do not force the tool – let the speed of the saw blade do the

work. Cutting performance will not improve by applying more pressure

on the tool and blade life will be reduced. When using the parallel guide,

ensure that it is parallel with the blade and not the base of the tool, as

otherwise the blade and motor could become damaged. To set the guide,

loosen the two retaining screws, and slide it up snugly against the side of

the work piece. Retighten the screws to secure it in the desired position.

Place front edge of saw squarely on work before starting motor. When

starting a cut, sight the cutting line with the line of cut guide taking care to

introduce the blade to the material slowly, so as not to damage its teeth.

Use both hands to move the saw forward through the work piece.

Laser Sight Guide System

An additional feature of this machine is the laser sight system, which is

Fig. 1

Fig. 2

Fig. 3

4 31

1 2 3 4 5 6 7 8 9 ... 32 33

Kommentare zu diesen Handbüchern

Keine Kommentare

Evolution EVO230-HDX Bedienungsanleitung Seite 4

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Kreissägen Evolution EVO230-HDX